Manufacturer of O Rings, O Ring Kits Rs.720/- Each, Oil Seals, Backup Rings, X Rings, Cords, Construction Material, Hydraulic Sealing Elements, Pneumatic Sealing Elements, Mumbai, India +(91) 9833548480; [email protected]; JIS B 2401 O-ring sizes. JIS B 2401: INNER DIAMETER(I.D) ID

O-R ing Standard Size (JIS B 2401) O-Ring Standard Size (JIS B 2401) JIS B 2401 SIZE MEASUREMENTS IN MILLIMETERS MEASUREMENTS IN INCHES ID ± CS ± ID ± CS ±

These o-ring sizes are unique to Japan’s automotive, semiconductor, and manufacturing industries. JIS O-Ring Groups. Aerospace Group. 367 sizes and follows ISO 3601-1 very

1. Male or Plug - the O-ring groove is located on a plug which is inserted into the housing or cylinder (fig. 1-23) 2. or Tube - the O-ring groove is located in the housing or cylinder

Japanese Industrial Standards (JIS) O-Ring Sizes JIS Size ID (mm) ID Tol' (+/- mm) CS (mm) CS Tol' (mm) ID (inch) ID Tol' (+/- inch) CS (inch) CS Tol' (inch) Seals | Gaskets | Bearings | Gears & Drives | Power Transmission | Fluid Power | Industrial Hose | Tools & Maintenance | Electro Mechanical Services | Integrated Solutions

Then, calculate the O-Ring groove diameter as follows: a. For a rod (shaft) seal:O-Ring Max Groove Diameter = Min Shaft Diameter + (2 x Recommended Gland Depth) b. For a bore (piston) seal:O-Ring Min Groove Diameter = Max Bore Diameter – (2 x Recommended Gland Depth) c.

sure act on the O-ring in the same direction. Groove design can reduce the tendency for extrusion. See figures 1-32 a & b. If the friction of the moving metal sur-face across the O-ring is in the same direction as the direction of the pres-sure, the O-ring will be dragged into the clearance gap more readily and thus extrude at about 35% of the

JIS B 2401 Metric O-Rings Size Chart JIS B 2401 is a Japanese Industrial Standard for O-Ring sizes. This standard, often referred to as “Japanese Metrics”, is organized into four series, based on their application. The O-Rings in each section have

548 rows · Standard Japanese O-Rings sizes. Tolerances vary by use, please see out tolerance pages. Thousands of non-standard sizes are available in stock or can be made within a few

O-rings are typically sized by their inside diameter and cross section, and are further specified by the type of compound used. For O-ring sizes other than standard sizes, specify the actual dimensions desired for the inside diameter (I.D.) and the cross section (W). There may be a tooling charge for such non-standards Configurator Seals Catalog

O-ring Groove Design in 3 easy steps: Step 1 Choose whether you are working with existing hardware or designing new hardware. Select the type of O-ring groove - piston, rod, face seal or trapped seal. If the O-ring size required is known, simply select the AS, BS or ISO standard (such as AS568) and enter the dash size reference.

207 rows · G45 O-Ring 3.1 0.1 44.4 0.41 0.62 0.49 G50 O-Ring 3.1 0.1 49.4 0.45 0.68 0.54 G55

Another general material specification standard is the Japanese Industrial Standard (JIS) B 2401 “O-rings.” The classification system recommended by this standard is twofold, by material and by size and use. The material classification is as follows: Next Topic Material Specifications Part 3, Other Specifications

Expert Application Engineering Assistance O-ring groove design guides offer default dimensional guidance on the most basic o-ring groove design applications. The best o-rings are useless without the right groove design which becomes increasingly important the more demanding the application environment.

The JIS B 2401 specification describes 1006 O-rings in three different groups: aerospace, general purpose, and traditional. The aerospace group describes 367 O-rings and matches the ISO 3601-1 standard very closely (with a few additional sizes). Each size is designated by its dimension: ID × cross-section.

You can also use anti-extrusion devices. An anti-extrusion device is a thin ring composed of hard plastic such as PTFE, Nylon and PEEK. Once in place, these rings will provide essentially zero clearance. Groove Dimensions - ISO 3601 Static Radial Applications Static Axial (Face) Applications Reciprocating Applications

PPE manufactures elastomer O-rings from a broad range of material grades to the following international standard O-ring sizes:- AS568 SAE (Society of Automotive Engineers) Standard O-ring sizes ISO3601 International Organisation for Standardisation (metric O-rings) British Standard BS1806 O-ring sizes (imperial)

Explore Groove Designs O-ring groove charts for standard O-ring gland designs.O-ring groove design recommendation FAQs. Popular o-ring size standards include USA's AS568 o-ring size chart, the UK's BS 1806 o-ring sizing chart, and Japan's JIS B 2401 o-ring size list. Metric o-rings and custom size o-rings are often used when a standard o

1. The following sizes are not normally recommended for dynamic service, although special applications may permit their use: -001 thru -003 -223 thru -284 -013 thru -050 -350 thru -395 -117 thru -178 -461 thru -475 2. Clearances shown are based on 70 durometer materials.

Expert Application Engineering Assistance. O-ring groove design guides offer default dimensional guidance on the most basic o-ring groove design applications. The best o-rings are useless without the right groove design which becomes increasingly important the more demanding the application environment. Review the general o-ring groove design

JIS B 2401 O-RING SIZE CHART 1005 Warner Ave, Suite A Lewiston ID 83501 | Phone (208) 413-6377 Fax (208) 413-6719 The Japanese Industrial Standard (JIS B 2401) lists 194 sizes of O-rings which are unique to Japan's automotive and manufacturing industries. JIS O-Rings consist of 4 series of sizes for different applications. These series include; P

Dimensions apply to all laterally loaded o’rings in static face seal grooves for both liquid pressure and vacuum applications. Groove Flange O’ring Cross Section (L) Groove Depth Squeeze (%)

41 rows · This metric o-ring groove design reference guide will help you find the right radius, back-up, pressure and other o-ring dimensions for basic applications. Once you find the exact metric

The most commonly found o’ring size standard, even in metric based machinery 0.070″ (1/16″ Nominal) 1.78mm Cross Section Show entries Showing 1 to 10 of 50 entries Previous Next 0.103” (3/32″ Nominal) 0.139” (1/8″ Nominal) 0.210” (3/16″ Nominal) 0.275” (1/4″ Nominal) SAE Straight Thread Boss Seals BS Extended Range

Please check the type/dimensions/specifications of the part G115-1A in the O-Ring JIS B 2401 - G Series (Static application) series. The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs . Similar Part Numbers Additional Products in this Category

jis size g30 metric o-ring buna-n (nbr) 70 duro black cs: 3.10 mm (0.122 in) id: 29.40 mm (1.157 in) Our Office is Closed for the Weekend. We Will Open at 8 am CST on Monday.